What was done to your JK this week?
02-01-2009, 10:01 PM
#4222
JK Super Freak
Join Date: May 2008
Location: Grand Junction, CO
Posts: 1,279
Likes: 0
Received 0 Likes
on
0 Posts
CTM's installed
I installed the CTM U-Joints in AlloyUSA front axle shafts and installed them. The CTM's are beefy suckers. A bit of a bitch to install into the yokes as the tolerances are tight. Also installed a Rock Krawler HD Tie Rod and replaced the leaking SS with a new Teraflex SS.
Hopefully sometime this coming week I'll have time to install the Superior rear axle shafts, B&M tranny cooler and the Aeroforce Interceptor Scan Gauge if it comes this week.
And I'm looking for the right 2 -3 gallon air tank to mount between the frame rails. They're all to big; nobody seems to make a skinny long one.
Hopefully sometime this coming week I'll have time to install the Superior rear axle shafts, B&M tranny cooler and the Aeroforce Interceptor Scan Gauge if it comes this week.
And I'm looking for the right 2 -3 gallon air tank to mount between the frame rails. They're all to big; nobody seems to make a skinny long one.
02-02-2009, 01:11 AM
#4223
JK Enthusiast
Join Date: Jun 2008
Location: Tonopah, Arizoooooooooonaaaa
Posts: 431
Likes: 0
Received 0 Likes
on
0 Posts
Well my front and rear bumpers came in and were installed by my goddy buddy John while I am over here and here it is, he also installed my Winch. No I have to decide on what lights to get for the front Bumper. Hmmmmmm it has 4 tabs for lights on it I think the top two are going to be rally HID lights and the outter ones a lil bit smaller since they would cover the turn sigs if to big. just gotta decide now. Hmmmm any suggestions?
02-02-2009, 04:57 AM
#4224
JK Freak
Join Date: Nov 2008
Location: Edmond,Oklahoma
Posts: 511
Likes: 0
Received 0 Likes
on
0 Posts
Well my front and rear bumpers came in and were installed by my goddy buddy John while I am over here and here it is, he also installed my Winch. No I have to decide on what lights to get for the front Bumper. Hmmmmmm it has 4 tabs for lights on it I think the top two are going to be rally HID lights and the outter ones a lil bit smaller since they would cover the turn sigs if to big. just gotta decide now. Hmmmm any suggestions?
02-02-2009, 07:30 AM
#4225
JK Enthusiast
Join Date: Jul 2008
Location: Waldwick, NJ
Posts: 406
Likes: 0
Received 0 Likes
on
0 Posts
Well my front and rear bumpers came in and were installed by my goddy buddy John while I am over here and here it is, he also installed my Winch. No I have to decide on what lights to get for the front Bumper. Hmmmmmm it has 4 tabs for lights on it I think the top two are going to be rally HID lights and the outter ones a lil bit smaller since they would cover the turn sigs if to big. just gotta decide now. Hmmmm any suggestions?
02-02-2009, 08:56 AM
#4226
JK Enthusiast
Join Date: Apr 2008
Location: long iland,ny
Posts: 132
Likes: 0
Received 0 Likes
on
0 Posts
I had purchased a set of stock 17. Inch with sra from someone on this site with the hopes of powder coating...gave up on the powder coating..took my 16. Steelies off and put on the 17....OH. Yeah. Much better makes the jeep look smaller but much better....
02-02-2009, 02:16 PM
#4230
JK Freak
Join Date: Mar 2008
Location: philly burbs
Posts: 681
Likes: 0
Received 0 Likes
on
0 Posts
After running over a spilled bucket of roofing nails, along with 17 other cars, I had to get new tires. The 3 temporary plugs in each tire were expectedly not holding air - which led to getting 4 new 35" BFG KM2's. Need to get the spare someday. While, I was at it ground down the pinch seem and shortened the Rubi rails. Relocated the cb antenna to the license plate holder and removed the spare tire rack. Will carry the 33 " when I go wheeling.