STUPID things you've done while working on your JK
#1
JK Super Freak
Thread Starter
STUPID things you've done while working on your JK
This thread is for anyone that has had one of those ,,, or moments while trying to mod their Jeep. Come on, we've all had them. Now you can go ahead and share your moment in the sun with the rest of the forum. Please try and hold off on the flaming. Everyone screws up at least once in their life. And to prove my point, I'll start.....
Over a month ago, I made a futile attempt to install my TF front lower control arms in my driveway, by myself. After a few hours of struggling to get the first one on, I gave up and re-installed the stock arm. Well, over a month and TWO wheeling trips later(one of which was a three hour drive one way), I decided that today was a good day to extend my breathers. I lay down under the Jeep and this is the first thing that I see...........
Over a month ago, I made a futile attempt to install my TF front lower control arms in my driveway, by myself. After a few hours of struggling to get the first one on, I gave up and re-installed the stock arm. Well, over a month and TWO wheeling trips later(one of which was a three hour drive one way), I decided that today was a good day to extend my breathers. I lay down under the Jeep and this is the first thing that I see...........
#3
JK Super Freak
Thread Starter
#4
JK Enthusiast
Join Date: May 2009
Location: NJ exile living near Baltimore
Posts: 459
Likes: 0
Received 0 Likes
on
0 Posts
I was installing new coil springs in 95 degree heat. I switched out the drivers side with no problem. I supported the axle with a floor jack and obviously had to lower it some to fit the taller spring. I brought the jack over the pasenger side and lowered the jack until I could pull the spring out. I then started to install the new spring. No matter what I tired it wouldn't fit. I pushed down on the axle and struggled to get it in, but it wasn't budging. I was sweating profusely due to the heat and was now getting light headed so I decided to take a break. I was sitting nearby drinking a cold beverage while comtemplating my next move. Would I have to give up and put the old springs back in?
After staring at the situation a little more, it dawned on me that the jack was still fully supporting the axle. I went over, lowered the jack and slipped the new spring in.
After staring at the situation a little more, it dawned on me that the jack was still fully supporting the axle. I went over, lowered the jack and slipped the new spring in.
#5
JK Super Freak
Join Date: Sep 2011
Location: Boston, MA
Posts: 1,012
Likes: 0
Received 0 Likes
on
0 Posts
I was topping off some oil on sunday, and aparently I left the funnel with the oil cap just sitting in the engine.... didnt even notice until tuesday.
I'm so smart >.<. Guess I'm off to pep boys to get a new oil filter....
I'm so smart >.<. Guess I'm off to pep boys to get a new oil filter....
#6
Missed with the hammer when persuading the rear rotors off. Didnt realize I hit the dust shield. Put everything back together, went for the test ride and had a horrible noise. Thought it was the parking brake shoes rubbing too much. Took everything back apart, adjusted them down, back together and still had noise. Back apart, stuck my head in there when spinning the hub, and was like....hey that not supposed to rub. With a little help from my trusty pliers, no more noise.
#7
JK Junkie
Join Date: Oct 2006
Location: Pottstown, PA
Posts: 2,466
Likes: 0
Received 0 Likes
on
0 Posts
I'm not to proud to admit my F-up ! While installing my RR front bumper i had the utility knife out to remove some of the factory zip ties for the fog lights. I proceeded to slice about a 1.5" long and deep gash in my finger with the knife and spent a few hours in the hospital getting stitched up... damn local anesthesia never took and were the most painful stitches I've ever had... damnit !!! The scar on my finger is a sad reminder of that day ... .
As soon as I got home from the hospital a few hours later I jumped right back on the install and finished it up...bandages and all. Bumper looks great !
As soon as I got home from the hospital a few hours later I jumped right back on the install and finished it up...bandages and all. Bumper looks great !
Trending Topics
#9
JK Enthusiast
Join Date: Jan 2011
Location: Searcy, AR
Posts: 221
Likes: 0
Received 0 Likes
on
0 Posts
Stupid shit that happened to me when someone else was working on my jk... Let's just say someone forgot to torque the bolts holding my brake caliper to the axle. I'm lucky I'm alive
#10
JK Enthusiast
Join Date: Nov 2010
Location: north dakota
Posts: 464
Likes: 0
Received 0 Likes
on
0 Posts
i was having a heck of a time putting my rear spring back in while installing my lift kit, i had a prybar pulling down with everything i had in me and the bar slipt out of my hand and the handle came up under my chin and knocked me out!!! i had a sore jaw for a month...