Smittybilt XRC!
#11
JK Enthusiast
Join Date: Jun 2009
Location: N.E. B.F.E. Indiana (Rome City)
Posts: 483
Likes: 0
Received 0 Likes
on
0 Posts
Cool man, my XRC front AND rear w/tire carrier will be here middle of next week
Can't wait!!!!!
Awsome look cpray, just makes me even more stoked!
Can't wait!!!!!
Awsome look cpray, just makes me even more stoked!
#12
JK Junkie
Join Date: Oct 2008
Location: North Texas
Posts: 2,060
Likes: 0
Received 0 Likes
on
0 Posts
#13
JK Newbie
Join Date: Nov 2007
Location: Scottsdale, az
Posts: 93
Likes: 0
Received 0 Likes
on
0 Posts
#16
JK Enthusiast
Join Date: Oct 2008
Location: Littleton, CO
Posts: 281
Likes: 0
Received 0 Likes
on
0 Posts
They all look awesome
This bumper is definitely on my list of future mods. Going to turn the stocker into a stubbie while waiting for funds to be available for the Smittybuilt.
It's good to hear that you all like yours!
This bumper is definitely on my list of future mods. Going to turn the stocker into a stubbie while waiting for funds to be available for the Smittybuilt.
It's good to hear that you all like yours!
#17
JK Enthusiast
Join Date: Feb 2009
Location: South Louisiana
Posts: 416
Likes: 0
Received 0 Likes
on
0 Posts
thanks for the props camp......i wish i could lie and say yes, so i could win a prize , but no i didn't paint them. they are sahara fenders. i chopped them so that the line would flow directly with my bumper. man, i wish you were closer cause i'm about to do a major upgrade on my ride........here is my build sheet:
upgrade axles to rubi D44's
5.38 gears
arb lockers
viair onboard air
rubicon express driveshafts front and rear
rubicon express 4.5" long arm
37" mtr kevlars
17" trailready beadlocks w/ black world series ring
expedition one rear bumper/tire carrier
redrock fab sliders with aluminum skins
any thoughts or suggestions for the build??
#19
JK Freak
Thread Starter
Join Date: Nov 2007
Location: Waterloo, Ontario
Posts: 575
Likes: 0
Received 0 Likes
on
0 Posts
Update!
Welp! shes finaly installed! heres the pics! and a bit of the story.
This is my brothers girlfriends parents place. Her dad has a shop out back. Her brother races dirt flat track motorcycles. 450/600. its some pretty cool stuff there was races there on the sat night that i got to see. a lot of harleys on custom frames but alot of modified dirtbikes as well.
So here is the install...
Testing for fit....
tightening up the nuts
centre punching the holes on the cross beam... turns out its little off? must of hit a rock hahaha
up on the lifting... doing the drilling for the holes
brothers gf trying to look tuff and pretend to hold up the jeep while its on the lift
stopping for some freshly deep fried chicken wings and beer! and yes my brother is pounding that beer back haha
next morning.... winch mounted...
bought some red paint for the fairlead and shackles.. i know it wont last long... but it was easy enough to do... wouldnt take much to do it every now and then... ohhh and i re-bedlined my grill with E-Z liner... the first time i did it, it didnt have much texture... i realized if you spray form a foot to a foot and half away it gives it a lot more of a rough surface and looks alot better!
10 bucks at canadian tire! booo yahh!!
lights are all wired up... just gotta drill a hole and put in a switch... right now i just have the wires wrapped up and tapped up in the engine bay... dont worry no loose wires and loose ends haha
and a few from a far.. not the best but when i get a chance to wash it all up ill take more pictures....
hope you all enjoy!!
This is my brothers girlfriends parents place. Her dad has a shop out back. Her brother races dirt flat track motorcycles. 450/600. its some pretty cool stuff there was races there on the sat night that i got to see. a lot of harleys on custom frames but alot of modified dirtbikes as well.
So here is the install...
Testing for fit....
tightening up the nuts
centre punching the holes on the cross beam... turns out its little off? must of hit a rock hahaha
up on the lifting... doing the drilling for the holes
brothers gf trying to look tuff and pretend to hold up the jeep while its on the lift
stopping for some freshly deep fried chicken wings and beer! and yes my brother is pounding that beer back haha
next morning.... winch mounted...
bought some red paint for the fairlead and shackles.. i know it wont last long... but it was easy enough to do... wouldnt take much to do it every now and then... ohhh and i re-bedlined my grill with E-Z liner... the first time i did it, it didnt have much texture... i realized if you spray form a foot to a foot and half away it gives it a lot more of a rough surface and looks alot better!
10 bucks at canadian tire! booo yahh!!
lights are all wired up... just gotta drill a hole and put in a switch... right now i just have the wires wrapped up and tapped up in the engine bay... dont worry no loose wires and loose ends haha
and a few from a far.. not the best but when i get a chance to wash it all up ill take more pictures....
hope you all enjoy!!
#20
JK Enthusiast
Join Date: Feb 2008
Location: Richmond Hill, ON
Posts: 428
Likes: 0
Received 0 Likes
on
0 Posts
Ugh, missed that the install was this weekend, not next. Still PM me and let me know when you're going back down to Welland, we can hook up, maybe do the canal banks.