Phoenix Area JK'ers Say your piece!
#5351
JK Super Freak
I was thinking of that since i finally have a garage big enough to work on the jeep in. im just lacking the tools such as jack stands, floor jack, 16,18,21mm wrenches and sockets ect
#5352
JK Super Freak
Join Date: Feb 2010
Location: New River/ Phoenix,AZ
Posts: 1,214
Likes: 0
Received 0 Likes
on
0 Posts
I have all of that. If you guys want to make the drive to my place Saturday we can do it there. Wife is leaving for a christmas party around 11am. Ill be doing some wrenching of my own for a bit saturday
#5353
JK Super Freak
However you may look at buying a few of them as time goes by. At some point you will want to check the tightness of a bolt, etc and will need a 18 mm socket or so. etc, etc.
#5354
JK Super Freak
#5355
JK Super Freak
Join Date: Feb 2010
Location: New River/ Phoenix,AZ
Posts: 1,214
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by remark
Are you doing your transfer case?
#5356
JK Freak
Join Date: Feb 2011
Location: The living room
Posts: 682
Likes: 0
Received 0 Likes
on
0 Posts
Transfer case spec.s:
CASE Material: 356-T6 Heat Treated Aluminum
Weight: 125 lbs. (dry)
INTERNAL COMPONENTS:
Gears: Helical Cut
Planetary Gears: 6 Gears Helical Cut
Bearings: Needle & Taper Rollers
Synchronizers: Borg Warner
Available Input Shaft Splines: 21, 23, 27, 29, 31, 32, 34
Tail Shaft H.D., 32 Spline 300M
Front Output 32 Spline
RATIOS:
Low Range: (2.0:1, 2.72:1, & 5.44:1) or (2.72:1, 3.0:1, & 8:16:1) or (2.72:1, 3.8:1, & 10.34:1) or (2.72:1, 4.3:1, & 11.70:1)
High Range 1:1
LUBRICATION:
Quarts: 2.5
CASE Material: 356-T6 Heat Treated Aluminum
Weight: 125 lbs. (dry)
INTERNAL COMPONENTS:
Gears: Helical Cut
Planetary Gears: 6 Gears Helical Cut
Bearings: Needle & Taper Rollers
Synchronizers: Borg Warner
Available Input Shaft Splines: 21, 23, 27, 29, 31, 32, 34
Tail Shaft H.D., 32 Spline 300M
Front Output 32 Spline
RATIOS:
Low Range: (2.0:1, 2.72:1, & 5.44:1) or (2.72:1, 3.0:1, & 8:16:1) or (2.72:1, 3.8:1, & 10.34:1) or (2.72:1, 4.3:1, & 11.70:1)
High Range 1:1
LUBRICATION:
Quarts: 2.5
#5357
JK Super Freak
Join Date: Feb 2010
Location: New River/ Phoenix,AZ
Posts: 1,214
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by Jknockers
Transfer case spec.s:
CASE Material: 356-T6 Heat Treated Aluminum
Weight: 125 lbs. (dry)
INTERNAL COMPONENTS:
Gears: Helical Cut
Planetary Gears: 6 Gears Helical Cut
Bearings: Needle & Taper Rollers
Synchronizers: Borg Warner
Available Input Shaft Splines: 21, 23, 27, 29, 31, 32, 34
Tail Shaft H.D., 32 Spline 300M
Front Output 32 Spline
RATIOS:
Low Range: (2.0:1, 2.72:1, & 5.44:1) or (2.72:1, 3.0:1, & 8:16:1) or (2.72:1, 3.8:1, & 10.34:1) or (2.72:1, 4.3:1, & 11.70:1)
High Range 1:1
LUBRICATION:
Quarts: 2.5
CASE Material: 356-T6 Heat Treated Aluminum
Weight: 125 lbs. (dry)
INTERNAL COMPONENTS:
Gears: Helical Cut
Planetary Gears: 6 Gears Helical Cut
Bearings: Needle & Taper Rollers
Synchronizers: Borg Warner
Available Input Shaft Splines: 21, 23, 27, 29, 31, 32, 34
Tail Shaft H.D., 32 Spline 300M
Front Output 32 Spline
RATIOS:
Low Range: (2.0:1, 2.72:1, & 5.44:1) or (2.72:1, 3.0:1, & 8:16:1) or (2.72:1, 3.8:1, & 10.34:1) or (2.72:1, 4.3:1, & 11.70:1)
High Range 1:1
LUBRICATION:
Quarts: 2.5
#5359
JK Newbie
Join Date: Nov 2011
Location: Somewhere in AZ
Posts: 44
Likes: 0
Received 0 Likes
on
0 Posts